MOTOROLA, INC. BITSURFR PRO EZ Card Type ISDN TA Chip Set Unidentified I/O Options Analog adapters (2) Transfer Rate 56Kbps x 2/64Kbps x 2 Data Bus Serial ISDN Protocol AIMux, PPP, V.120 Switch Type 5ESS, DMS-100, NI-1 [Image] CONNECTIONS Function Label Function Label DC power in CN1 Analog adapter 2 CN4 Serial port CN2 Analog adapter 1 CN5 ISDN U interface CN3 USER CONFIGURABLE SETTINGS Setting Label Position Factory configured - do not alter SW1/1 Off Factory configured - do not alter SW1/2 Off Factory configured - do not alter SW1/3 Off Normal operation SW1/4 Off TA will reset to factory defaults when powered SW1/4 On up DIAGNOSTIC LED(S) LED Color Status Condition LS Red On Power is on LS Green On TA is ready for operation LS Red/Green Blinking ISDN not synchronized LS N/A Off Power is off 1 Green On Call is connected on analog adapter 1 1 Green Blinking Call is being connected on analog adapter 1 1 Green Off Analog adapter 1 is idle 2 Green On Call is connected on analog adapter 2 2 Green Blinking Call is being connected on analog adapter 2 2 Green Off Analog adapter 2 is idle DTE Green On Data call connected with V.120 DTE Green Slow blink Data call being connected DTE Green Blinking Data call connected with single-channel protocol DTE Green Fast blink Data call connected with multi-channel protocol DTE Green Off Data call not connected RD Unidentified On TA is receiving data RD Unidentified Off TA is not receiving data TD Unidentified On TA is transmitting data TD Unidentified Off TA is not transmitting data SUPPORTED STANDARD COMMANDS Basic AT Commands +++, A/ A, E, H, O, V, W, X, Z &F, &S, &W, &Y, &Z Extended AT Commands \Q S-Registers S0, S1, S2, S3, S4, S5, S7, S10, S12, S18, S25 Note: See MHI help file for complete information. Proprietary AT Command Set BEARER CHANNEL - DATA Type: Configuration Format: AT [cmds] %A98=x [cmds] Description: Selects the Bearer Channel the TA will use for data calls. Command Function %A98=A TA will use 3.1KHz audio Bearer Channel. %A98=D TA will use data Bearer Channel. %A98=S TA will use speech Bearer Channel. BEARER CHANNEL - ANALOG ADAPTER 1 Type: Configuration Format: AT [cmds] *1%A98=x [cmds] Description: Selects the Bearer Channel the TA will use for calls that are made with analog adapter 1. Command Function *1%A98=A TA will use 3.1KHz audio Bearer Channel. *1%A98=S TA will use speech Bearer Channel. BEARER CHANNEL - ANALOG ADAPTER 2 Type: Configuration Format: AT [cmds] *2%A98=x [cmds] Description: Selects the Bearer Channel the TA will use for calls that are made with analog adapter 2. Command Function *2%A98=A TA will use 3.1KHz audio Bearer Channel. *2%A98=S TA will use speech Bearer Channel. CALL ANSWERING - 3.1KHz AUDIO Type: Configuration Format: AT [cmds] %A94=x [cmds] Description: Selects whether the TA will auto-answer incoming calls using the 3.1KHz audio Bearer Channel. Command Function %A94=D TA will not answer call. %A94=E TA will answer call. CALL ANSWERING - DATA Type: Configuration Format: AT [cmds] %A95=x [cmds] Description: Selects whether the TA will auto-answer incoming calls using the data Bearer Channel. Command Function %A95=D TA will not answer call. %A95=E TA will answer call. CALL ANSWERING - SPEECH BEARER Type: Configuration Format: AT [cmds] %A93=x [cmds] Description: Selects whether the TA will auto-answer incoming calls using the speech Bearer Channel. Command Function %A93=D TA will not answer call. %A93=E TA will answer call. CALL BUNDLING Type: Configuration Format: AT [cmds] @B0=n [cmds] Description: Selects whether the TA will make two-channel ISDN data calls. Command Function @B0=1 Call bundling disabled. @B0=2 Call bundling enabled. CALLER ID Type: Immediate Format: AT [cmds] @Ln [cmds] Description: Displays or clears the Caller ID log. Command Function @L0 Clears the Caller ID log. @L1 Displays the most recent Caller ID entry. @L2 Displays all Caller ID entries. CALLER ID AUTO-DISPLAY Type: Configuration Format: AT [cmds] @N1=n [cmds] Description: Selects whether the TA will automatically display Caller ID information upon receiving an incoming call. Command Function @N1=0 Caller ID auto-display disabled. @N1=1 Caller ID auto-display enabled. CALLER ID LOGGING Type: Configuration Format: AT [cmds] @N0=n [cmds] Description: Selects whether the TA will log Caller ID information. Command Function @N0=0 Caller ID logging disabled. @N0=1 Caller ID logging enabled. CALLER ID SECURITY Type: Configuration Format: AT [cmds] @IS=x [cmds] Description: Selects which type of security will be used with the Caller ID database. Command Function @IS=B Call blocking enabled. @IS=D Call security disabled. @IS=S Call screening enabled. CALLER ID SECURITY - ADD Type: Configuration Format: AT [cmds] @IA=<#> [cmds] Description: Adds the number specified to the Caller ID security list. CALLER ID SECURITY - CLEAR Type: Configuration Format: AT [cmds] @IC [cmds] Description: Clears the Caller ID security table. CALLER ID SECURITY - COPY TO DATA PORTS Type: Configuration Format: AT [cmds] @IP [cmds] Description: Copies the Caller ID security table to all data ports. CALLER ID SECURITY - COPY TO VOICE PORTS Type: Configuration Format: AT [cmds] @IV [cmds] Description: Copies the Caller ID security table to all voice ports. CALLER ID SECURITY - DELETE Type: Configuration Format: AT [cmds] @ID=<#> [cmds] Description: Deletes the number specified from the Caller ID security list. CALLER ID SECURITY - DISPLAY Type: Immediate Format: AT [cmds] @IL [cmds] Description: Displays the Caller ID security table. CHAP PASSWORD Type: Configuration Format: AT [cmds] @M20="xxxx" [cmds] Description: Sets the password the TA will send at connection for CHAP authentication if CHAP authentication is requested and no password is provided within the dialing command. CONFIGURATION WRITE PROTECTION Type: Configuration Format: AT [cmds] @G=x [cmds] Description: Selects whether the user may store changes to the TA's configuration. Command Function @G=D Write protection disabled. @G=E Write protection enabled. DATA LENGTH Type: Configuration Format: AT [cmds] @P4=n [cmds] Description: Sets the length of the data words the TA is receiving from the serial port. Command Function @P4=7 TA uses seven data bits. @P4=8 TA uses eight data bits. DATA PARITY Type: Configuration Format: AT [cmds] @P3=x [cmds] Description: Sets the parity of the data the TA is receiving from the serial port. Command Function @P3=E TA uses even parity. @P3=M TA uses mark parity. @P3=N TA uses no parity. @P3=O TA uses odd parity. DATA STOP Type: Configuration Format: AT [cmds] @P6=n [cmds] Description: Sets the number of stop bits the TA is receiving from the serial port. Command Function @P6=0 TA uses one stop bit. @P6=1 TA uses one and one half stop bits. @P6=2 TA uses two stop bits. DCD SIGNAL Type: Configuration Format: AT [cmds] &Cn [cmds] Description: Configures the behaviour of the DCD signal. Command Function &C0 DCD forced high. &C1 DCD normal. &C2 DCD forced high except during disconnect. DIAL Type: Immediate Format: AT [cmds] D<#>;[cmds] Description: Dials the telephone number indicated according to any modifiers included in the string. Command Function DS=n Dial stored telephone number n. D>P="xxxx" Dial and send CHAP password xxxx. D; Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. DIAL MODE Type: Configuration Format: AT [cmds] %A97=x [cmds] Description: Selects the type of dialing the TA will use. Command Function %A97=E Enbloc dialing enabled. %A97=O Overlap dialing enabled. DIRECTORY NUMBER - DATA Type: Configuration Format: AT [cmds] !N1=<#> [cmds] Description: Sets the DN for data calls. DIRECTORY NUMBER - ANALOG ADAPTER 1 Type: Configuration Format: AT [cmds] *1!N1=<#> [cmds] Description: Sets the DN for analog adapter 1. DIRECTORY NUMBER - ANALOG ADAPTER 2 Type: Configuration Format: AT [cmds] *2!N1=<#> [cmds] Description: Sets the DN for analog adapter 2. DISPLAY COMMAND SETTINGS Type: Immediate Format: AT [cmds] >V=x [cmds] Description: Displays the specified command settings. Command Function >V=C Displays ISDN switch configuration. >V=G Displays global command settings. DISPLAY COMMAND SETTINGS Type: Immediate Format: AT [cmds] &V=x [cmds] Description: Displays the specified command settings. Command Function &V Displays port settings. &V=E Displays V.120 command settings. &V=Z DIsplays stored telephone numbers. DISPLAY FIRMWARE VERSION Type: Immediate Format: AT [cmds] $Q [cmds] Description: Displays the firmware version number. DISPLAY HELP SCREEN Type: Immediate Format: AT [cmds] &H=xxxx,xxxx,xxxx... [cmds] Description: Displays the help screen for the command or commands indicated. If no commands are listed, a generic help screen of a list of all supported commands will be displayed. DISPLAY INFORMATION Type: Immediate Format: AT [cmds] In [cmds] Description: Displays information requested about the modem. Command Function I0 Displays product identification code. I1 Displays ROM checksum. I2 Tests and displays ROM checksum result. I3 Displays board number, firmware revision, and checksum result. I4 Displays product ID, supported protocols, firmware date and revision in numeric format. I8 Displays product ID, supported protocols, firmware date and revision. I9 Displays Plug-N-Play information. I10 Displays ISDN connection information. DTR DIALING Type: Configuration Format: AT [cmds] &Ln [cmds] Description: Selects whether the TA will automatically dial the first stored number when DTR is low and no call is connected. Command Function &L0 DTR dialing disabled. &L1 DTR dialing enabled. DTR SIGNAL Type: Configuration Format: AT [cmds] &Dn [cmds] Description: Configures the behavior of the DTR signal. Command Function &D0 DTR forced high. &D1 TA will enter command mode on low DTR. &D2 TA will disconnect on low DTR. &D3 TA will disconnect and reset on low DTR. &D9 DTR dialing enabled. ECHO CANCELLATION TONE Type: Configuration Format: AT [cmds] %A96=n [cmds] Description: Selects whether the TA will generate an echo cancellation tone. Command Function %A96=0 Echo cancellation tone disabled. %A96=1 Echo cancellation tone enabled. FACTORY DEFAULT PROFILE - ISDN SWITCH Type: Configuration Format: AT [cmds] >F [cmds] Description: Returns the command settings pertaining to the ISDN switch configuration to the values found in the factory default profile. FIRMWARE UPGRADE Type: Immediate Format: AT [cmds] $Y=xxxxxx [cmds] Description: Begins a firmware upgrade session with the password indicated. FIRMWARE UPGRADE PASSWORD Type: Configuration Format: AT [cmds] %P1=xxxxxxxx [cmds] Description: Sets the password required to upgrade the firmware to the string indicated. The password must be eight characters or less, case sensitive. If the password is set to a capital D, the password check will be disabled. ISDN FEATURE - CONFERENCE CALL Type: Configuration Format: AT [cmds] !V3=n [cmds] Default: 60 Range: 1 - 63 Unit: N/A Description: Selects the ISDN feature code for conference calling. ISDN FEATURE - DROP CALL Type: Configuration Format: AT [cmds] !V4=n [cmds] Default: 62 Range: 1 - 63 Unit: N/A Description: Selects the ISDN feature code for call dropping. ISDN FEATURE - TRANSFER CALL Type: Configuration Format: AT [cmds] !V5=n [cmds] Default: 61 Range: 1 - 63 Unit: N/A Description: Selects the ISDN feature code for call transferring. ISDN FEATURE - VOICEMAIL WAITING Type: Configuration Format: AT [cmds] !V8=n [cmds] Default: 63 Range: 1 - 63 Unit: N/A Description: Selects the ISDN feature code for waiting voicemail. LINE SPEED Type: Configuration Format: AT [cmds] %A4=n [cmds] Description: Selects the speed at which the TA will connect. Command Function %A4=0 Line speed set to 64Kbps. %A4=1 Line speed set to 56Kbps. LOCAL SERIAL PORT SPEED Type: Configuration Format: AT [cmds] @P2=n [cmds] Description: Sets the speed of the local serial port. Command Function @P2=300 Sets serial port speed to 300bps. @P2=1200 Sets serial port speed to 1200bps. @P2=2400 Sets serial port speed to 2400bps. @P2=4800 Sets serial port speed to 4800bps. @P2=9600 Sets serial port speed to 9600bps. @P2=19200 Sets serial port speed to 19.2Kbps. @P2=38400 Sets serial port speed to 38.4Kbps. @P2=57600 Sets serial port speed to 57.6Kbps. @P2=115200 Sets serial port speed to 115.2Kbps. @P2=230400 Sets serial port speed to 230.4Kbps. This disables serial port speed auto-detection. PROTOCOL - B-CHANNEL Type: Configuration Format: AT [cmds] %A2=n [cmds] Description: Selects the rate adaptation protocol the TA will use. Command Function %A2=2 V.120 protocol selected. %A2=3 PPP protocol selected. %A2=95 AIMux protocol selected. RESULT CODES Type: Configuration Format: AT [cmds] Qn [cmds] Description: Enables TA to send result codes to the DTE. Command Function Q0 Result codes enabled. Q1 Result codes disabled. Q2 Result codes enabled in originate mode only. SERVICE PROFILE ID - DATA Type: Configuration Format: AT [cmds] !C6=<#> [cmds] Description: Sets the SPID for data calls. SERVICE PROFILE ID - ANALOG ADAPTER 1 Type: Configuration Format: AT [cmds] *1!C6=<#> [cmds] Description: Sets the SPID for analog adapter 1. SERVICE PROFILE ID - ANALOG ADAPTER 2 Type: Configuration Format: AT [cmds] *2!C6=<#> [cmds] Description: Sets the SPID for analog adapter 2. SET DATE Type: Configuration Format: AT [cmds] >D0=mm/dd/yy [cmds] Description: Sets the internal clock to the date specified. SET TIME Type: Configuration Format: AT [cmds] >D1=hh:mm:ss [cmds] Description: Sets the internal clock to the time specified. SOFT RESET Type: Immediate Format: AT [cmds] >Z [cmds] Description: Resets TA and command settings pertaining to the ISDN switch configuration to the stored profile. STORE ISDN SWITCH CONFIGURATION Type: Configuration Format: AT [cmds] >W [cmds] Description: Writes the values for the commands pertaining to the ISDN switch configuration into the non-volatile RAM. SWITCH TYPE Type: Configuration Format: AT [cmds] !C0=n [cmds] Description: Selects the type of ISDN switch the TA is connected to. Command Function !C0=0 TA is connected to AT&T 5ESS switch. !C0=1 TA is connected to Northern Telecom DMS-100 switch. !C0=2 TA is connected to National NI-1 switch. SWITCH VERSION Type: Configuration Format: AT [cmds] !C1=n [cmds] Description: Selects the version of ISDN switch the TA is connected to. Command Function !C1=0 TA is connected to 5ESS point-to-point switch. !C1=1 TA is connected to 5ESS multipoint switch. !C1=2 TA is connected to DMS-100 PVC IC-0 switch. !C1=3 TA is connected to DMS-100 PVC IC-1 switch. !C1=4 TA is connected to NI-1 switch. TERMINAL ENDPOINT IDENTIFIER - DATA Type: Configuration Format: AT [cmds] !D3=n [cmds] Default: 255 Range: 0 - 63, 127, 255 Unit: N/A Description: Selects the TEI for data calls. A value of 127 disables the TEI, and a value of 255 causes the TA to auto-select the TEI. TERMINAL ENDPOINT IDENTIFIER - ANALOG ADAPTER 1 Type: Configuration Format: AT [cmds] *1!D3=n [cmds] Default: 255 Range: 0 - 63, 127, 255 Unit: N/A Description: Selects the TEI for analog adapter 1. A value of 127 disables the TEI, and a value of 255 causes the TA to auto-select the TEI. TERMINAL ENDPOINT IDENTIFIER - ANALOG ADAPTER 2 Type: Configuration Format: AT [cmds] *2!D3=n [cmds] Default: 255 Range: 0 - 63, 127, 255 Unit: N/A Description: Selects the TEI for analog adapter 1. A value of 127 disables the TEI, and a value of 255 causes the TA to auto-select the TEI. TEST MODES Type: Immediate Format: AT [cmds] &Tn Description: Selects test options. Command Function &T0 End current test. &T1 Begin local analog loopback test. &T3 Begin local digital loopback test. &T8 Begin bilateral loopback est &T9 Begin terminal loopback test. V.120 MAXIMUM RECEIVE FRAME SIZE Type: Configuration Format: AT [cmds] %E1=n [cmds] Default: 256 Range: 1 - 260 Unit: 1 byte Description: Sets the maximum frame size for transmission in V.120 mode. V.120 MAXIMUM TRANSMIT FRAME SIZE Type: Configuration Format: AT [cmds] %E0=n [cmds] Default: 256 Range: 1 - 260 Unit: 1 byte Description: Sets the maximum frame size for transmission in V.120 mode. V.120 TRANSMISSION TIMER Type: Configuration Format: AT [cmds] %E3=n [cmds] Default: 5 Range: 1 - 255 Unit: Unidentified Description: Sets the T200 transmission timer for V.120 mode. V.120 WINDOW SIZE Type: Configuration Format: AT [cmds] %E2=n [cmds] Default: 8 Range: 1 - 127 Unit: 1 byte Description: Sets the window size for V.120 mode.